Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing occurred? Look inside the tank, and you could see no water inside. Before you stress, relax knowing that fixing this problem is usually easy to accomplish. If you can’t complete this yourself, you can always arrange toilet repair with a knowledgeable plumber. Follow these recommendations to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first move is to ensure that the water is flowing. If you or someone in your household recently performed a toilet repair, you most likely turned off the water first. Did you forget to turn it back on? To see, turn the water shut-off valve on the wall in back of the toilet. If the valve was turned off, water ought to now start refilling the tank. If this fails to work, check the water at your sink or another plumbing fixture. If nothing comes out from the tap, you could possibly have a more substantial water supply issue. Phone your water company to get more details. 

Reposition or Replace the Float Mechanism 

Older toilet brands use a float ball to measure the water level as it rises in the tank. When the ball reaches a specific height, the float arm it’s connected to stops the water flow. However, insufficient water might enter the tank if the ball is positioned incorrectly or the arm is faulty. To correct the float ball, start by removing the toilet tank lid. Bend the float arm up a little to adjust where it sits in the tank. If this fails to fix the problem, you may need to replace the whole float mechanism. You should be able to complete this yourself by following the detailed steps that come with the replacement parts, or you can work with a plumber for help. Just note that float balls are old toilet design. You may prefer improved durability and efficiency if you upgrade the existing tank components or replace the toilet altogether. 

Adjust the Fill Valve 

Newer toilets use a float cup instead of a float ball, coupled with a fill valve and water level rod. There could quite possibly be no water in the toilet tank because the valve has slipped out of place or become blocked. Here are techniques to consider: 

• Modify the fill valve: Look inside the toilet and locate the fill valve on top of a vertical tube device on the left side of the tank. Make sure it’s secure and evenly attached to the tube. Then, adjust the water level. More modern toilets have an adjustment knob you can turn manually, while older versions may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and allow the tank refill to test the water level. Adjust it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
• Clean the fill valve: Mineral buildup and other crud might be covering the valve and stopping your toilet from filling. Shut off the water behind the toilet and take away the fill cap. Then, steadily turn the water back on, cupping your hand over the valve to prevent water from spraying all over the place. After several seconds, turn the water back off. Finally, scrub the fill cap to remove hard water buildup. If the cap is damaged, buy a new one. 
• Clean the valve tube: The tube below the fill valve might also be plugged. Shut off the water and remove the valve hardware. Then, insert a slim bottle brush or wire down the tube. Turn the water back on a little to flush away the junk. Replace the valve hardware and flush the toilet to check your efforts. 

Repair or Replace the Trip Assembly 

If you’ve attempted the steps above without positive results, the final possibility is a damaged trip assembly. This part links the flush handle to the tank. If it’s not working or positioned improperly, the flush cycle may not complete, leaving the tank void. Detach the toilet tank lid and look at the trip assembly fastened to the handle. If it’s out of place, reposition it. If the assembly is crooked, worn or broken, change it out. Whether you complete the job yourself or leave it to a plumber, this simple repair should get your toilet tank filled with water once more. 

Schedule Toilet Repair Today 

You can’t go long without a working toilet, so reach out to [Company name] to schedule a toilet repair. We can determine why your toilet isn’t filling and recommend the right fix. If your plumbing fixture is older and worn out, our team can easily install a high-efficiency toilet in your home. Be assured that every plumbing repair and replacement we conduct is backed by a 100% satisfaction guarantee. To schedule a visit from one of our licensed professionals, please call your community Service Experts Heating, Air Conditioning & Plumbing office today.